GE IC600FP832K / IC600BF832K Input Module | Replacement, Equivalent & Selection Guide
The GE IC600FP832K (also catalogued as IC600BF832K) is a discrete input module designed for the General Electric Series Six programmable logic controller platform. Engineered for high-reliability industrial environments, this module serves as the primary digital signal acquisition interface between field devices and the Series Six CPU. Konmask.com supplies both new-surplus and professionally refurbished units, fully tested to OEM performance standards.
Technical Specifications
| Parameter | Specification |
|---|---|
| Part Number | IC600FP832K / IC600BF832K |
| Manufacturer | General Electric (GE Automation) |
| Module Type | Discrete / Digital Input Module |
| Platform | GE Series Six PLC |
| Input Voltage | 120 VAC (nominal) |
| Number of Input Points | 32 points |
| Input Signal Type | Discrete (ON/OFF) |
| Isolation | Optical isolation between field and logic circuits |
| Backplane Interface | Series Six parallel I/O bus |
| Operating Temperature | 0 °C to +60 °C |
| Relative Humidity | 5% – 95% non-condensing |
| Form Factor | Single-slot Series Six I/O rack module |
| Weight | Approx. 560 g |
| Approvals | UL Listed; CE compliant |
Compatible Replacement & Equivalent Models
When the IC600FP832K / IC600BF832K is unavailable or end-of-life, the following models may serve as functional equivalents or drop-in replacements depending on system configuration. Always verify rack slot compatibility and firmware revision before substitution.
| Model | Type | Compatibility Notes |
|---|---|---|
| IC600FP832 | Earlier revision | Same form factor; verify firmware compatibility |
| IC600BF832 | Base variant | Functionally equivalent; suffix K denotes revision level |
| IC600FP816K | 16-point input variant | Reduced I/O count; use when full 32-point density not required |
| IC600FP864K | 64-point input variant | Higher density; confirm rack power budget |
| IC693MDL645 | GE Series 90-30 (90 series) | Different platform — requires rack and CPU migration |
Note: Cross-platform replacements require engineering review. Contact Konmask technical support for a validated substitution assessment.
Why Choose the Original Model
- Proven platform longevity: Series Six systems remain operational in legacy power, water, and manufacturing facilities worldwide; maintaining original hardware avoids costly platform migrations.
- Exact electrical compatibility: The IC600FP832K is factory-matched to Series Six backplane timing and bus protocols — no firmware patches or adapter cards required.
- Optical isolation integrity: OEM isolation ratings are certified; third-party equivalents may not meet the same dielectric withstand specifications.
- Reduced commissioning risk: Drop-in replacement with no PLC program modification needed when replacing like-for-like.
- Regulatory traceability: Original part numbers maintain audit trails for ISO, FDA, and NERC-CIP compliance environments.
Typical Applications
- Power generation plant auxiliary control systems (turbine, boiler, BOP)
- Water and wastewater treatment SCADA I/O expansion
- Petrochemical and refinery process interlocks
- Pulp and paper mill drive and conveyor control
- Automotive assembly line discrete signal acquisition
- Legacy building management and HVAC control panels
- Mining and minerals processing equipment monitoring
System Compatibility
| Component | Compatible Series Six Hardware |
|---|---|
| CPU Modules | IC600CPU522, IC600CPU524, IC600CPU526, IC600CPU528 |
| I/O Racks | IC600YB831, IC600YB832, IC600YB833 (Series Six I/O racks) |
| Power Supplies | IC600PS501, IC600PS502 |
| Programming Software | Logicmaster 6 (LM6); compatible with GE Proficy Machine Edition via legacy gateway |
| Communication Modules | IC600CM551 (Genius Bus); IC600CM552 (Serial) |
Selection Guide
- Step 1 — Platform verification: Confirm your controller is a GE Series Six (not Series 90, PACSystems, or VersaMax). Check the CPU faceplate label.
- Step 2 — I/O count: Verify you require 32 discrete input points per slot. If fewer points are needed, consider IC600FP816K to reduce wiring density.
- Step 3 — Voltage level: Confirm field device output voltage is 120 VAC. For 24 VDC field devices, a different input module variant is required.
- Step 4 — Rack slot availability: Confirm an open I/O slot exists in the target rack and that rack power budget supports an additional input module.
- Step 5 — Revision suffix: The suffix “K” denotes a specific hardware revision. Match the revision to your existing installed base to ensure consistent behavior.
- Step 6 — Spare or active replacement: For active replacement, confirm the PLC program I/O address mapping matches the target slot assignment before installation.
Quality Assurance & Sourcing
- Functional test protocol: Every unit undergoes powered bench testing — input channel verification, optical isolation check, and backplane communication validation prior to shipment.
- Traceability: Units are tagged with inspection records including test date, technician ID, and pass/fail log.
- Packaging: Anti-static ESD bags, foam-lined cartons, and fragile labeling as standard.
- Warranty: 12-month replacement warranty against defects in materials and workmanship.
- Sourcing transparency: Konmask sources from decommissioned OEM installations, authorized distributors, and certified refurbishers — no counterfeit risk.
How to Order
- Add the IC600FP832K / IC600BF832K to your cart on Konmask.com.
- For volume orders (>3 units) or urgent requirements, email support@konmask.com for a dedicated quote within 4 business hours.
- Provide your shipping address and preferred carrier (DHL, FedEx, UPS, or sea freight for bulk).
- Payment accepted via T/T bank transfer, PayPal, and major credit cards.
- Export documentation (commercial invoice, packing list, COO) provided for international shipments.
Replacement & Compatibility FAQ
Q: Is IC600FP832K the same as IC600BF832K?
A: Yes. The “FP” and “BF” prefixes reflect GE’s internal catalog classification changes over production runs. Both part numbers refer to the same physical module with identical electrical specifications.
Q: Can I use this module in a GE Series 90-30 rack?
A: No. The Series Six and Series 90-30 use different backplane architectures and are not physically or electrically interchangeable.
Q: Do I need to modify my PLC program after replacing this module?
A: Not if you install the replacement in the same rack slot. The I/O address mapping is slot-based in Series Six; a like-for-like swap requires no program changes.
Q: What is the lead time for in-stock units?
A: In-stock units ship within 1–2 business days. Contact us to confirm current availability before placing time-critical orders.
Q: Can Konmask provide a test report with the shipment?
A: Yes. A functional test report is available upon request at no additional charge.
Q: Is this module compatible with Logicmaster 6 programming software?
A: Yes. The IC600FP832K is fully compatible with Logicmaster 6 (LM6) for I/O configuration and diagnostics.
© 2026 Konmask.com. All rights reserved.
Original Source: https://Konmask.com
Contact: support@konmask.com | +0086 19859288691
