Bently Nevada 330103-00-02-05-01-00 Proximity Probe | Replacement, Equivalent & Selection Guide
The Bently Nevada 330103-00-02-05-01-00 is an eddy-current proximity probe designed for continuous, non-contact measurement of shaft vibration, position, and eccentricity in rotating machinery. It is a core component of the Bently Nevada 3300 XL series monitoring system, widely deployed in turbines, compressors, pumps, and other critical rotating equipment.
Technical Specifications
- Part Number: 330103-00-02-05-01-00
- Manufacturer: Bently Nevada (Baker Hughes)
- Series: 3300 XL 8mm Proximity Transducer System
- Probe Tip Diameter: 8 mm
- Cable Length: 2 m (integral cable)
- Extension Cable Length: 5 m
- Sensitivity: 7.87 V/mm (200 mV/mil)
- Linear Range: 0.25 – 2.25 mm (10 – 90 mil)
- Frequency Response: DC – 10,000 Hz
- Operating Temperature: -35°C to +177°C (probe); -35°C to +85°C (driver)
- Supply Voltage: -24 VDC (nominal)
- Output Voltage: -1 VDC to -21 VDC
- Connector: Integral coaxial, reverse-mount
- Housing Material: Stainless steel
- Approvals: CE, ATEX, FM (intrinsically safe options available)
- Weight: Approx. 260 g (probe + cable assembly)
Compatible Replacement & Equivalent Models
The following models are commonly used as direct or functional replacements for the 330103-00-02-05-01-00. Always verify system compatibility before substitution.
- Bently Nevada 330103-00-02-10-02-00 — Same series, 10 m extension cable variant
- Bently Nevada 330103-00-02-05-02-00 — Armored cable version, same probe geometry
- Bently Nevada 330104-00-02-05-01-00 — 3300 XL 11mm probe, compatible driver/monitor
- Epro PR6423/010-040 — 8mm eddy-current probe, compatible with Bently Nevada monitors via signal conditioning
- Metrix ST5484E — Functional equivalent for non-contact vibration measurement; requires driver verification
- Emerson CSI 330103 series — OEM-equivalent supplied under Emerson/Baker Hughes branding
Note: Third-party equivalents may require recalibration of the monitoring system. Consult your system integrator before replacement.
Why Choose the Original Model
- Factory-calibrated sensitivity matched to Bently Nevada 3300 XL drivers and monitors
- Guaranteed interoperability with 3300/3500 series monitoring racks without reconfiguration
- Traceable quality — each probe ships with a calibration certificate and lot traceability
- Long-term availability — Konmask maintains stock of legacy and current-generation Bently Nevada probes
- Reduced commissioning risk in safety-critical and API 670-compliant installations
Typical Applications
- Steam and gas turbine shaft radial vibration monitoring
- Centrifugal compressor rotor position and thrust measurement
- Pump and motor bearing journal monitoring
- Gearbox and expander eccentricity measurement
- API 670 machinery protection systems
- Petrochemical, power generation, and LNG plant rotating equipment
System Compatibility
- Monitors: Bently Nevada 3300, 3500, 3701, 3703 series
- Drivers: Bently Nevada 330180, 330130, 330190 series proximitors
- Extension Cables: 330130-045-00-00, 330130-080-00-00 and compatible 3300 XL extension cables
- Target Material: AISI 4140 steel (standard); consult factory for non-standard alloys
- Gap Voltage at Midrange: -10.5 VDC ± 0.5 V (with standard driver)
Selection Guide
Use the table below to select the correct 330103 variant for your application:
- Probe cable length: 02 = 2 m integral cable (standard) | 05 = 5 m | 09 = 9 m
- Extension cable length: 05 = 5 m | 10 = 10 m | 15 = 15 m
- Connector type: 01 = standard coaxial | 02 = armored
- Approval code: 00 = standard | 01 = ATEX/IECEx | 02 = FM
For the part number 330103-00-02-05-01-00: 8mm probe, 2 m cable, 5 m extension, standard connector, no special approval. This is the most common configuration for general industrial use.
If your installation requires a longer extension cable, armored cable, or hazardous-area certification, contact Konmask for the correct variant.
Quality Assurance & Sourcing
- All units sourced from authorized distributors or verified surplus channels with full traceability
- Pre-shipment inspection: visual, dimensional, and electrical verification
- Calibration certificate available upon request
- Anti-counterfeit verification: serial number and label authentication
- Packaging: original OEM packaging or equivalent ESD-safe packaging
- Warranty: 12 months from date of shipment
How to Order
- Online: Add to cart directly on this page
- Email: support@konmask.com — include part number, quantity, and required delivery date
- Phone/WhatsApp: +0086 19859288691
- Lead time: In-stock items ship within 1–3 business days; ex-stock orders confirmed at time of inquiry
- Payment: T/T, PayPal, credit card, and trade terms available for qualified accounts
Replacement & Compatibility FAQ
Q: Can I use a 330104 (11mm) probe as a replacement for the 330103 (8mm)?
A: Not directly. The 11mm probe has a different linear range and sensitivity. The mounting hole and target gap must be redesigned. Use only as a replacement if the mechanical installation is modified accordingly.
Q: Is the 330103-00-02-05-01-00 compatible with the Bently Nevada 3500 monitor?
A: Yes, when paired with the correct 3300 XL proximitor driver. The 3500 monitor accepts the standard -24 VDC / 200 mV/mil signal output.
Q: Can third-party probes (e.g., Epro, Metrix) replace this unit without recalibration?
A: Functional replacement is possible, but the monitoring system must be recalibrated to the replacement probe’s sensitivity curve. This is required for API 670 compliance.
Q: What is the recommended gap voltage for installation?
A: Set the probe gap to achieve approximately -10.5 VDC at the driver output, corresponding to the midpoint of the linear range (approximately 1.25 mm gap).
Q: Do you provide calibration certificates?
A: Yes. Calibration certificates are available upon request for all units. Please specify at time of order.
© 2026 Konmask.com. All rights reserved.
Original Source: https://Konmask.com
Contact: support@konmask.com | +0086 19859288691


