Bently Nevada 190501-16-00-CN Velomitor CT Velocity Transducer | Replacement, Equivalent & Selection Guide
The Bently Nevada 190501-16-00-CN is a high-performance Velomitor CT (Compact Top-exit) velocity transducer designed for continuous vibration monitoring of rotating machinery. This page provides full technical specifications, compatible replacement models, and a structured selection guide to help engineers and procurement teams make confident sourcing decisions.
Technical Specifications
| Parameter | Value |
|---|---|
| Part Number | 190501-16-00-CN |
| Brand / Manufacturer | Bently Nevada (Baker Hughes) |
| Series | Velomitor CT |
| Sensor Type | Velocity Transducer (Seismic) |
| Output Signal | Voltage proportional to velocity |
| Sensitivity | 100 mV/in/s (4 mV/mm/s) |
| Frequency Range | 2 Hz – 2,000 Hz |
| Measurement Range | 0 – 50 in/s pk (0 – 1,270 mm/s pk) |
| Supply Voltage | 18 – 30 VDC (24 VDC nominal) |
| Operating Temperature | -40°C to +121°C (-40°F to +250°F) |
| Connector / Exit | Top-exit, 2-pin MIL-C-5015 connector |
| Housing Material | Stainless Steel |
| Ingress Protection | IP67 |
| Weight | Approx. 380 g |
| Approvals | CE, ATEX (consult datasheet for zone ratings) |
| Compatible Monitor | Bently Nevada 3500 Series, 1900/65A |
Compatible Replacement & Equivalent Models
The following models are commonly evaluated as replacements or equivalents for the 190501-16-00-CN. Always verify electrical and mechanical compatibility before substitution.
| Model | Brand | Type | Compatibility Notes |
|---|---|---|---|
| 190501-16-00 | Bently Nevada | Velomitor CT (side-exit variant) | Same series, different connector exit; verify cable routing |
| 190501-08-00-CN | Bently Nevada | Velomitor CT (shorter cable) | Identical sensor, shorter integral cable |
| 330500-02-CN | Bently Nevada | Velomitor XA (extended range) | Higher temp rating; check monitor input compatibility |
| VM-2000 | Metrix (Roper Technologies) | Velocity Transducer | Drop-in equivalent for many 3500 applications; verify sensitivity |
| ST-5000 | Wilcoxon Sensing Technologies | Seismic Velocity Sensor | Similar frequency range; confirm connector pinout |
| VS-068 | Hansford Sensors | Industrial Velocity Sensor | Cost-effective alternative; verify output impedance |
⚠ Disclaimer: Third-party equivalents listed are for reference only. Konmask.com recommends using genuine Bently Nevada parts for safety-critical applications. Contact us for compatibility verification.
Why Choose the Original Model
- Guaranteed compatibility with Bently Nevada 3500 Series and 1900/65A monitoring systems
- Factory-calibrated sensitivity traceable to NIST standards
- Proven reliability in continuous 24/7 machinery protection environments
- Full OEM documentation including calibration certificates and material traceability
- ATEX / CE certified for use in hazardous area installations
Typical Applications
- Steam and gas turbine casing vibration monitoring
- Centrifugal compressor bearing housing measurement
- Pump and motor vibration surveillance
- Fan and blower seismic monitoring
- Gearbox and expander condition monitoring
- Integration with Bently Nevada 3500/42M, 3500/46M, and 1900/65A modules
System Compatibility
The 190501-16-00-CN is designed for direct integration with the following Bently Nevada monitoring platforms:
- Bently Nevada 3500 Series – Machinery Protection System (MPS)
- Bently Nevada 1900/65A – General Purpose Equipment Monitor
- System 1 – Condition Monitoring & Diagnostic Software (via compatible I/O modules)
For third-party DCS/PLC integration (Siemens, Rockwell, Honeywell, ABB), a signal conditioner or transmitter may be required to convert the voltage output to 4–20 mA.
Selection Guide
Use the criteria below to confirm the 190501-16-00-CN is the correct model for your application:
| Selection Criteria | Requirement | 190501-16-00-CN |
|---|---|---|
| Connector exit direction | Top-exit (CN suffix) | ✅ Yes |
| Operating temperature | Up to +121°C | ✅ Yes |
| Frequency range | 2 – 2,000 Hz | ✅ Yes |
| Monitor compatibility | Bently Nevada 3500 / 1900/65A | ✅ Yes |
| Hazardous area rating | ATEX / CE required | ✅ Yes |
| Cable length | 16 ft (approx. 4.9 m) integral cable | ✅ Yes (suffix -16) |
If your application requires a higher temperature rating (>121°C), consider the 330500-02-CN Velomitor XA. For 4–20 mA output, a signal conditioner such as the Bently Nevada 3300/55 is recommended.
Quality Assurance & Sourcing
- Source: Authorized distributor stock and verified surplus channels
- Inspection: All units inspected for physical integrity and original packaging
- Documentation: Calibration certificates and material traceability available on request
- Lead Time: In-stock units ship within 1–3 business days; contact us for ETA on special orders
- Warranty: 12-month warranty against manufacturing defects
How to Order
- Confirm part number: 190501-16-00-CN
- Specify quantity and required delivery date
- Request a formal quotation via support@konmask.com or the product page cart
- Provide end-user application details if ATEX documentation is required
- Payment via T/T, PayPal, or credit card; export documentation available for international orders
Replacement & Compatibility FAQ
Q: Can the 190501-16-00-CN replace the 190501-16-00 (without CN suffix)?
A: The CN suffix denotes a top-exit connector configuration. The non-CN variant has a side-exit connector. They are electrically identical but mechanically different — verify your cable routing before substitution.
Q: Is the 190501-16-00-CN compatible with the Bently Nevada 3500/42M Vibration Monitor?
A: Yes. The Velomitor CT series is fully compatible with the 3500/42M Velocity Input module.
Q: Can I use a Metrix VM-2000 as a direct replacement?
A: The VM-2000 offers similar specifications and is used as a replacement in many installations. However, sensitivity calibration and connector pinout must be verified against your specific monitor configuration.
Q: Do you provide calibration certificates?
A: Yes. Calibration certificates are available for all new units. Contact us at support@konmask.com to request documentation.
Q: What is the lead time for the 190501-16-00-CN?
A: In-stock units typically ship within 1–3 business days. Contact us for current stock status and expedited shipping options.
© 2026 Konmask.com. All rights reserved.
Original Source: https://Konmask.com
Contact: support@konmask.com | +0086 19859288691






