Bently Nevada 330980-71-05 — Non-Contact Shaft Vibration Sensor | 3300 XL Proximitor Series
Engineering Background
The Bently Nevada 3300 XL Proximitor Series represents the industry benchmark for eddy-current proximity sensing in rotating machinery protection systems. Developed under Baker Hughes’ Bently Nevada division, the 3300 XL platform is engineered to meet the stringent demands of API 670-compliant machinery protection, delivering sub-micron resolution and long-term signal stability in the harshest industrial environments.
Product Positioning
The 330980-71-05 is a Non-contact Shaft Vibration (NSV) Proximitor Sensor designed for direct integration with Bently Nevada 3300 XL monitor systems. It serves as the primary transducer for radial vibration, axial position, and differential expansion measurement on turbines, compressors, pumps, and other critical rotating assets. Procurement engineers specify this part for new installations, MRO replacement, and system upgrades where OEM signal compatibility is mandatory.
Complete Technical Specifications
| Part Number | 330980-71-05 |
| Brand / OEM | Bently Nevada (Baker Hughes) |
| Series | 3300 XL NSV Proximitor |
| Sensing Technology | Eddy-current (non-contact) |
| Measurement Type | Radial vibration, axial position, differential expansion |
| Output Signal | -18 VDC nominal (standard Bently Nevada scale factor) |
| Scale Factor | 200 mV/mil (7.87 V/mm) — 3300 XL standard |
| Linear Range | Per probe/cable/proximitor system calibration |
| Supply Voltage | -24 VDC (nominal) |
| Operating Temperature | -35 °C to +85 °C (electronics module) |
| Enclosure Rating | IP66 / NEMA 4X |
| Hazardous Area Approval | FM, CSA, ATEX (consult datasheet for specific certifications) |
| Connector Type | Standard Bently Nevada coaxial |
| Compatible Monitors | 3300 XL series (3300/16, 3300/20, 3300/25, 3300/46, 3300/55) |
| Compatible Probes | 3300 XL 8 mm, 11 mm probe series |
| Weight | ~100 g |
| Compliance | API 670, CE |
Proven Application Environments
- Steam & Gas Turbines — shaft radial vibration and axial thrust position monitoring
- Centrifugal Compressors — continuous rotor dynamic surveillance per API 670
- Boiler Feed Pumps & Large Pumps — bearing housing and shaft relative vibration
- Gearboxes — gear mesh frequency and shaft orbit analysis
- Electric Motors (>1 MW) — rotor eccentricity and air-gap monitoring
- Expanders / Turboexpanders — high-speed rotor protection in cryogenic service
- Offshore & Petrochemical Platforms — salt-spray and high-humidity environments
Engineering Advantages
- OEM Signal Compatibility — drop-in replacement for existing 3300 XL installations; no recalibration of monitor cards required when replacing like-for-like
- High EMI Immunity — coaxial signal path and internal shielding reject VFD and high-voltage interference common in industrial switchgear rooms
- Wide Temperature Stability — maintains scale factor accuracy across -35 °C to +85 °C without field adjustment
- IP66 / NEMA 4X Sealing — suitable for outdoor, washdown, and high-humidity installations without additional enclosure
- Long Service Life — solid-state eddy-current design with no moving parts; MTBF >100,000 hours in typical service
- Hazardous Area Rated — FM/CSA/ATEX approvals support installation in Zone 1/2 and Division 1/2 classified areas
System Architecture & Signal Flow
The 330980-71-05 operates as the signal-conditioning module within the classic Bently Nevada three-component proximity system:
- Probe (tip) — generates the eddy-current field at the shaft surface
- Extension Cable — transmits the raw oscillator signal from probe to Proximitor
- Proximitor (330980-71-05) — conditions the signal, provides -24 VDC oscillator drive, and outputs a calibrated DC voltage proportional to gap distance
- 3300 XL Monitor Card — receives the conditioned output, applies alarm/danger setpoints, and communicates to DCS/SIS
The total system cable length (probe + extension) must match the Proximitor’s calibrated range. Verify the probe part number and extension cable length against the 330980-71-05 calibration certificate before installation.
Sourcing & Quality Verification
- Units sourced from authorized distributors, OEM surplus, and verified MRO channels
- Each unit inspected for physical integrity, connector condition, and label authenticity prior to dispatch
- Calibration certificates and original packaging available upon request (subject to stock condition)
- Traceability documentation (lot number, manufacture date) provided where available
- Konmask does not sell counterfeit, refurbished-as-new, or unverified grey-market parts
Procurement Process
- Confirm compatibility — verify your existing probe part number and extension cable length match the 330980-71-05 system calibration
- Request a quote — contact support@konmask.com for volume pricing, lead time, and documentation requirements
- Place order — purchase order accepted via email; proforma invoice issued within 1 business day
- Shipping — DHL / FedEx international express; EXW Xiamen or CIF destination available
- After-sales — 12-month warranty against manufacturing defects; DOA replacement within 7 days of receipt
Technical FAQ
Q: Can the 330980-71-05 be used with non-Bently Nevada probes?
A: Not recommended. The Proximitor is factory-calibrated as a matched system with specific Bently Nevada probe and cable combinations. Using third-party probes will invalidate the scale factor and may produce erroneous readings.
Q: What is the difference between the 330980-71-05 and other 330980 variants?
A: The suffix (-71-05) denotes the specific cable length and connector configuration. Always match the full part number to your existing system documentation to ensure correct fit.
Q: Is this part API 670 compliant?
A: Yes. The 3300 XL Proximitor system is designed and tested to meet API 670 (5th Edition) requirements for machinery protection instrumentation.
Q: Do you provide calibration certificates?
A: Original OEM calibration certificates are provided where available. Please specify your documentation requirements at the time of inquiry.
Q: What is the lead time?
A: In-stock units ship within 2–3 business days. For out-of-stock items, typical lead time is 2–4 weeks. Contact us for real-time availability.
© 2026 Konmask.com. All rights reserved.
Original Source: https://Konmask.com
Contact: support@konmask.com | +0086 19859288691
